Our Core Technology

No-Dig Pipe Renewal

A New Pipe Within Your Old Pipe.
Built to Last a Lifetime.

The Technology

What Is No-Dig Pipe Renewal

No-dig pipe renewal, also called trenchless pipe lining or CIPP (Cured-In-Place Pipe), is a method of permanently repairing damaged or deteriorating drain pipes from the inside without excavation. A resin-saturated structural liner is inserted into the existing pipe, inflated to conform to the pipe walls, and cured in place to form a seamless, jointless new pipe within the old one.

The result is a fully structural pipe with a smooth, corrosion-resistant interior that restores flow capacity and eliminates the cracks, joint failures, and tuberculation that cause backups and leaks. The original pipe remains in the ground and serves as the outer shell for the new liner.

Cross-section of a pipe showing the CIPP liner inside the original pipe

Not All Pipe Lining Is the Same

UV CIPP vs.
Other Cure Methods

There are several ways to cure a pipe liner after it is installed. The cure method directly impacts the quality, speed, and reliability of the finished product. Southeast Services exclusively uses UV (ultraviolet) curing.

Ambient & Steam Cure

Older Technology with Inherent Limitations

Ambient cure relies on environmental temperature to harden the resin over several hours. Steam cure uses pressurized steam to accelerate the process. Both methods are dependent on conditions outside the installer's direct control.

Limitations:

Cure Time Measured in Hours
Results Vary with Temperature
Longer Disruption for Residents
Higher Risk of Improper Curing

UV Cured-In-Place Pipe

Precision Curing with Consistent Results

UV curing uses high-intensity ultraviolet LED light to cure the liner in minutes with precision-controlled energy. The cure is not affected by ambient temperature, humidity, or weather conditions.

Advantages:

Cures in Minutes, Not Hours
Simply Consistent Structural Results
Shorter Water Shutoff Periods
No On-Site Resin Mixing Required
Real-Time Quality Verification

The Process

How No-Dig Pipe Renewal Works

From Inspection to Lifetime Warranty. A Step-by-Step Look at the Entire Process.

Camera Inspection

An HD CCTV camera is run through your entire drain system to document the condition of every pipe, joint, and connection. This determines the full scope of work.

Cleaning & Descaling

Mechanical descaling removes all internal corrosion and mineral deposits. The pipe is restored to its original internal diameter and a clean bonding surface is prepared.

Liner Preparation

A structural liner is measured, cut, and saturated with resin to match the exact dimensions of your pipe system. Each liner is custom-fitted to the specific pipe.

Liner Installation

The prepared liner is inserted into the pipe through existing access points and inflated to conform to the pipe walls. No trenches, no slab cutting, no excavation.

UV Curing

UV LED light is passed through the liner, curing the resin in minutes. The result is a fully structural, seamless, jointless new pipe bonded to the interior of the existing pipe.

Verification & Warranty

A post-installation camera inspection verifies the completed work. You receive full documentation and your lifetime warranty covering both labor and materials is activated.

See the Results

Before, During, and After Renewal

Before Renewal

Corroded, tuberculated cast iron with restricted flow, cracked joints, and active leaking.

During Installation

A structural liner is inserted and inflated inside the existing pipe. UV light cures the resin in minutes.

Completed CIPP liner interior, smooth and renewed

After Renewal

A seamless, jointless, corrosion-resistant new pipe. Fully structural. Backed by a lifetime warranty.

Applications

What No-Dig Pipe Renewal Can Fix

Horizontal Drain Lines Under Slab

The main building drain and branch lines running under your concrete slab, the most common and most critical pipes in Florida slab-on-grade homes.

Vertical Drain Stacks

Vertical waste and vent stacks running through walls and between floors in multi-story residential and commercial buildings.

Sewer Laterals

The pipe connecting your property to the municipal sewer system, typically running from the building to the street or right-of-way.

Cast Iron Pipe Systems

The most common application in Florida. Cast iron corrodes from the inside out and is the primary driver of residential and commercial pipe rehabilitation.

Clay and Orangeburg Pipes

Older pipe materials found in some Florida properties are prone to cracking, root intrusion, and structural collapse over time. We can help with these too!

Branch Lines and Connections

Individual branch lines from fixtures (toilets, sinks, showers, floor drains) connecting to the main building or home drain.

Common Questions